{ "revision": "ON4CRD-RK-R2", "status": "passed", "runner_sha256": "7774e434c9bbb301c1d846123d069cf83ef844ed056a0dd290feb0742cb2b0d5", "simulator": "avr8js 0.21.0", "clock_hz": 16000000, "hardware_tested": false, "calibration_values_are_synthetic": true, "external_swr_reference_v": 3, "modelled_watchdog": true, "limitations": [ "No physical RF detector, reference accuracy, PhotoMOS delay, transceiver or bootloader execution is modeled.", "The reference diagnostic is a wide nominal-bandgap plausibility check, not a precision AREF measurement.", "ADC stuck at a plausible constant cannot be distinguished from a real stable carrier by software alone." ], "firmware": [ { "id": "cw", "source_sha256": "18ac1336ebe7dbf07509def8cff59d727e249dbe1d25390204e827db60fa564f", "hex_sha256": "e1839abaa3fb3f3f200d018793be9e6467062dfb3dfa8cea4de1477a85a8d463" }, { "id": "swr", "source_sha256": "9182a1951e6bfcbaaca0755ed58bd44ae7122272cac8ac28bddd7e2b1af12be8", "hex_sha256": "84ac68fd63d585b7cee4127966282093b82306e90d7ff478473fc73233266815" } ], "tests": [ { "name": "single dot", "edges": [ { "on": true, "ms": 53.5320625 }, { "on": false, "ms": 113.4871875 } ], "marks": [ 59.955125 ] }, { "name": "held dot repeats without release tail", "edges": [ { "on": true, "ms": 53.5320625 }, { "on": false, "ms": 113.517 }, { "on": true, "ms": 173.5515 }, { "on": false, "ms": 233.5338125 }, { "on": true, "ms": 293.568 }, { "on": false, "ms": 353.54975 } ], "marks": [ 59.984937499999994, 59.982312500000006, 59.981750000000034 ] }, { "name": "new tap of same paddle during mark is remembered", "edges": [ { "on": true, "ms": 53.5320625 }, { "on": false, "ms": 113.4990625 }, { "on": true, "ms": 173.535125 }, { "on": false, "ms": 233.5209375 } ], "marks": [ 59.96699999999999, 59.98581250000001 ] }, { "name": "contact bounce below four milliseconds is ignored", "edges": [], "marks": [] }, { "name": "small speed ADC noise preserves element timing", "edges": [ { "on": true, "ms": 53.5320625 }, { "on": false, "ms": 113.4959375 }, { "on": true, "ms": 204.060125 }, { "on": false, "ms": 264.0161875 }, { "on": true, "ms": 353.5628125 }, { "on": false, "ms": 413.526125 } ], "marks": [ 59.963874999999994, 59.9560625, 59.96331249999997 ] }, { "name": "iambic A squeeze release", "edges": [ { "on": true, "ms": 53.5339375 }, { "on": false, "ms": 113.4919375 } ], "marks": [ 59.958000000000006 ] }, { "name": "iambic B single opposite tail", "edges": [ { "on": true, "ms": 53.5339375 }, { "on": false, "ms": 113.49175 }, { "on": true, "ms": 173.5614375 }, { "on": false, "ms": 353.52575 } ], "marks": [ 59.957812499999996, 179.9643125 ] }, { "name": "boot held paddle remains unarmed", "edges": [], "marks": [] }, { "name": "5 WPM timing", "edges": [ { "on": true, "ms": 53.531 }, { "on": false, "ms": 293.5070625 } ], "marks": [ 239.9760625 ] }, { "name": "40 WPM timing", "edges": [ { "on": true, "ms": 53.5316875 }, { "on": false, "ms": 83.49075 } ], "marks": [ 29.95906250000001 ] }, { "name": "CW changing mode during squeeze cannot change its tail", "edges": [ { "on": true, "ms": 53.5339375 }, { "on": false, "ms": 113.4919375 } ] }, { "name": "CW STOP opens key and requires 250 ms released paddles", "serial": "RK-CW R2; 5..40 WPM; STOP/STATUS; 30 s continuous limit\r\nREADY\r\nSTOP; release paddles 250 ms\r\nRK-CW R2 WPM=5 MODE=A STATE=RELEASE TO REARM\r\nREADY\r\nRK-CW R2 WPM=5 MODE=A STATE=READY\r\n" }, { "name": "CW diagnostic UART flood leaves key timing bounded", "release": { "on": false, "ms": 113.524125 } }, { "name": "CW 30 s continuously held paddle times out and releases safely", "limit_ms": 30000, "final_state": 0, "serial": "RK-CW R2; 5..40 WPM; STOP/STATUS; 30 s continuous limit\r\nREADY\r\nTIMEOUT 30 s; release paddles 250 ms\r\nREADY\r\nRK-CW R2 WPM=5 MODE=A STATE=READY\r\n" }, { "name": "CW watchdog feed failure resets compiled sketch with held-paddle inhibit", "watchdog_ms": 2048, "virtual_fault": "WDR feed suppressed", "serial": "RK-CW R2; 5..40 WPM; STOP/STATUS; 30 s continuous limit\r\nREADY\r\nRK-CW R2; 5..40 WPM; STOP/STATUS; 30 s continuous limit\r\n" }, { "name": "SWR R2 empty EEPROM requires measured calibration", "lcd": [ "1.8 F0 R0 ", "CAL REQUIRED " ] }, { "name": "SWR rejects malformed and oversized six-knot commands without mutation", "commands": [ "SET -1 F 0 100", "SET 9 F 0 100", "SET 65536 F 0 100", "SET 0 F -1 100", "SET 0 F 6 100", "SET 0 F 0 2", "SET 0 F 0 1019", "SET 0 F 0 65539", "SET 0 F 0 4294967295", "SET 0 F 0 100x", "SET 0 F 0 100 trailing", "SET 0 FF 0 100", "SET 0 R 0 100SET 0 R 0 100SET 0 R 0 100SET 0 R 0 100" ] }, { "name": "SWR partial draft cannot become active or be saved; DISCARD restores", "lcd": [ "1.8 F0 R0 ", "CAL REQUIRED " ] }, { "name": "SWR APPLY validates paired six-knot curves and marks unsaved RAM", "lcd": [ "F 1.00 W 1.8M ", "SWR <1.58 *RAM " ] }, { "name": "SWR APPLY alone never persists a calibration across power cycle" }, { "name": "SWR R2 paired calibration survives journal save and reboot", "eeprom_slot_bytes": 256, "record_bytes": 246, "serial": " 0 0 0 0 0\r\nRK-SWR R2 SCHEMA=2 KNOTS=6 GENERATION=1 DIRTY=0 STORAGE=EEPROM\r\nREFERENCE=COARSE CHECK OK; verify 3.000 V\r\nRAW 0 0 0\r\n" }, { "name": "SWR duplicate SAVE does not rewrite EEPROM", "observed_write_operations": 0 }, { "name": "SWR nonmonotonic draft cannot replace previously active calibration" }, { "name": "SWR journal selects newest valid generation and falls back after latest CRC damage" }, { "name": "SWR power loss during actual journal writes preserves prior calibration", "cut_after_write_operations": 40 }, { "name": "SWR CRC-corrupt or legacy R1 EEPROM cannot produce calibrated output" }, { "name": "SWR near-total reflection is bounded on LCD", "lcd": [ "F 10.00 W 1.8M ", "SWR >99.9 " ] }, { "name": "SWR reverse below 50 mW reports nominal floor bound, never a fictitious 1:1", "lcd": [ "F 1.00 W 1.8M ", "SWR <1.58 " ] }, { "name": "SWR exact 1/5/10 W anchors stay exact and nominal upper bounds round conservatively", "anchors_w": [ 1, 5, 10 ], "upper_bounds": [ "1.58", "1.23", "1.16" ] }, { "name": "SWR reverse above calibrated domain is rejected", "lcd": [ "1.8 F750 R751 ", "REVERSE / RANGE " ] }, { "name": "SWR forward above calibrated domain is not extrapolated", "lcd": [ "1.8 F751 R0 ", "OVER RANGE " ] }, { "name": "SWR below 1 W forward suppresses numerical SWR", "lcd": [ "1.8 F249 R0 ", "FWD <1W / CHECK " ] }, { "name": "SWR rail saturation suppresses values and RAW fits 16 columns", "lcd": [ "1.8 F1023 R1023 ", "ADC SATURATION " ] }, { "name": "SWR unstable sample window suppresses a misleading averaged reading", "lcd": [ "1.8 F260 R0 ", "UNSTABLE / CHECK" ] }, { "name": "SWR external-reference band selection keeps boundary hysteresis", "transitions": [ 0, 0, 0, 0, 1, 1, 1, 0 ] }, { "name": "SWR missing reference keeps ADC switch disabled and requires explicit recheck", "lcd": [ "1.8 F0 R0 ", "FWD <1W / CHECK " ] }, { "name": "SWR gross reference change latches fault before calibrated output", "lcd": [ "REFERENCE FAULT ", "CHECK 3V / USB " ] }, { "name": "SWR timed-out partial command cannot splice into a later valid edit" } ] }